探讨缩聚催化剂对聚酯切片质量的影响

通过试验，分析比较了江西Sb2O3、南宁Sb2O3和大连Sb(Ac)3三种缩聚催化剂对聚酯切片质量的影响。试验结果表明，Sb(Ac)3是优良的缩聚催化剂。     

45钢表面超音速电弧喷涂Ti-Al涂层的组织与性能研究

采用自行开发研制的超音速电弧喷设备，在45钢表面制成了钛铝合金复合涂层。并利用金相显微镜、X射线衍射仪、扫描电镜、电子探针，对涂层的成分、相结构、显微组织及其结合强度、显微硬度进行了研究。结果表明，利用超音速电弧喷涂设备，可以在45钢表面形成 度高、孔隙率低，结合强度较好和硬度高的Ti-Al合金涂层。     

高温预析出对Al-Zn-Mg系铝合金时效硬化和应力腐蚀的影响

研究了高温固溶后降温处理工艺对中强可使预析出LC52和7039铝合金的组织、时效硬化和应力腐蚀的影响。金相观察发现,高温预析出可优先在晶界处产生,并提高随后时效状态下晶界析出相的不连续分布程度,温度降低到一定程度晶内和晶界产生大量析出。合金拉伸性能和应力腐蚀结果表明,预析出在保持强度和塑性的同时,可提高抗应力腐蚀性能。而预析出温度降低,合金强度呈下降趋势。     

Influence of inhibitor addition on the corrosion protection performance of sol–gel coatings on AA2024

Sol–gel films are actively investigated during the last decade as possible candidates for environmentally friendly pre-treatments. However, the important drawback in this case is the lack of active corrosion protection and self-healing ability.     

催化裂化汽油选择性加氢脱硫催化剂RSDS-1的开发

介绍了用于催化裂化汽油选择性加氢脱硫催化剂RSDS-1的研究开发，考察了载体、活性组元、金属原子比以及助剂对催化剂选择性的影响。研究结果表明，催化裂化汽油中烯烃的加氢饱和受扩散限制；Co—Mo组合对烯烃饱和的能力相对较弱；较高的Co／Mo原子比有利于提高催化剂选择性；助剂的加入对催化剂选择性有明显的影响；RSDS—1催化剂用于催化裂化汽油选择性脱硫，对不同原料油适应性好，脱硫率可达80％，RON损失小于2个单位，且可长周期稳定运转。     

Immobilization and activation of vanadium(III) and titanium(III) single‐site catalysts for ethylene polymerization using MgCl2‐based supports

Significant increases in the activity of vanadium(III) amidinate catalysts for ethylene polymerization have been obtained by immobilization on a MgCl₂‐based support prepared by reaction of AlEt₃ with a MgCl₂/ethanol adduct. Catalyst immobilization and activation on this type of support prevents the rapid decay in activity observed under homogeneous polymerization conditions with unsupported catalysts. Stable polymerization activity is also observed with analogous titanium(III) complexes. Polyethylene with narrow molecular weight distribution and spherical particle morphology is obtained without reactor fouling. Copyright © 2005 Society of Chemical Industry     

不饱和烃硅氢加成催化剂固载化研究进展

综述了各类负载过渡金属的催化剂体系及其在不饱和烃硅氢加成反应中的应用。负载过渡金属的催化剂具有良好的可回收性和选择性，研究主要集中在开发价廉、使用安全、环境友好和高催化性能的活性炭、氧化物或有机聚合物等负载过渡金属催化剂，并取得很好的结果。     

FeBP非晶态合金超细微粒的合成及其对PH3分解的催化作用

用化学还原法合成了FeBP非晶态合金超细微粒，用电感耦合等离子体光谱（ICP）、X射线粉末衍射（XRD）、透射电子显微镜（TEM）和差热分析（DSC）等手段对其进行了物性表征，并用微型催化反应装置考察了其对PH3分解的催化作用，结果表明，非晶态合金FeBP对PH3的分解具有良好的催化作用，能使PH3的分解温度从800℃以上降到500℃左右。490℃时分解率超过90％，540℃时达100％。     

Preparation of Plate Fe_(60)Co_8Zr_(10)Mo_5W_2B_(15) Bulk Amorphous Alloy and Its Fracture Toughness

1Introduction Duwez[1]synthesizedthefoilAu Siamorphousalloyforthefirsttimewithrapidsolidification,whichinitiatedthepreparationofamorphousalloysintheprocessofalloysolidification,andthereaftertheresearchonamorphousal loysdevelopedrapidly.Since1980s,withthec…     

Ni catalyst promotion of a Cis-selective Pd catalyst for canola oil hydrogenation

A Ni catalyst was added to a cis-selective Pd catalyst in an attempt to further improve the Pd catalyst's cis-selectivity and activity for canola oil hydrogenation. The system was tested under reaction conditions known to be suitable for cis-selective hydrogenation with the Pd catalyst (50 ppm Pd, 70 °C, and 5.2 MPa). Although inactive on its own under these conditions, the addition of 100 ppm Ni increased the hydrogenation activity (from 2.12 to 2.49 10⁻² min⁻¹). Further addition of Ni up to 1000 ppm resulted in no further improvements in activity. The trans isomer contents of the oils hydrogenated with Pd and the Pd/Ni systems were similar. The level of conjugated dienes decreased rapidly during hydrogenation with both Pd alone and with the Pd/Ni combination and no changes in conjugation were detected in the presence of the Ni catalyst alone. The increased activity of the Pd/Ni system over Pd alone was attributed to adsorption of catalyst poisons from the oil by Ni.